Can't take a trick:Epsom CX5500 with win98SE

Jason James · Jun 23, 2008

Howdy

I found an office supply place who also sold printers/scanner/copiers
(allin one). They had spec sheets in frames for each, and I found more than
one which could run on win98SE,..no earlier tho.

Went to a larger electronics place which sold printers etc and selected an
end of run Epsom CX5500 (2007 model).

I set it up and tried the next USB port and error message "cant communicate
with USBPRNT1). Checked Epsoms copy function and all OK. The thing appears
to be working.

Tried removing the new KB. reinstate the old one with the 1/4" circle plug/
This left the 2 USBs unused. Plugged Epsom into USB-1 reran the install CD,
all OK, but when tried to print it still cant communicate with USB port.
Appreciate any ideas on this,....Jason

MEB · Jun 24, 2008

Need specs for computer - make and model

You might try this:
Make sure the device is NOT connected when installing the software, wait
until it prompts you or restarts.
Since you have already installed the device, remove and uninstall, and
retry using this suggestion.

Printer
OPERATING SYSTEMS
PRINTER DRIVERS Win 98SE/Me/2000/XP/XP x64/Vista, Mac OS 10.2.8 or later
with USB / OS 10.5 Bundle available on CD

INTERFACE
INTERFACE USB 1.1 - Compatible with the USB 2.0 Specification

Drivers/Software
http://tech.epson.co.nz/downloads/p...mailAdd=&MetricIDReturned=124875&platform=w98

--
MEB
http://peoplescounsel.orgfree.com
--
_________

"Jason James" <at@peace.com> wrote in message
news:486062af$0$96064$c30e37c6@pit-reader.telstra.net...
| Howdy
|
| I found an office supply place who also sold printers/scanner/copiers
| (allin one). They had spec sheets in frames for each, and I found more
than
| one which could run on win98SE,..no earlier tho.
|
| Went to a larger electronics place which sold printers etc and selected an
| end of run Epsom CX5500 (2007 model).
|
| I set it up and tried the next USB port and error message "cant
communicate
| with USBPRNT1). Checked Epsoms copy function and all OK. The thing appears
| to be working.
|
| Tried removing the new KB. reinstate the old one with the 1/4" circle
plug/
| This left the 2 USBs unused. Plugged Epsom into USB-1 reran the install
CD,
| all OK, but when tried to print it still cant communicate with USB port.
| Appreciate any ideas on this,....Jason
|
|

Franc Zabkar · Jun 24, 2008

On Tue, 24 Jun 2008 12:59:18 +1000, "Jason James" <at@peace.com> put
finger to keyboard and composed:

>Howdy
>
> I found an office supply place who also sold printers/scanner/copiers
>(allin one). They had spec sheets in frames for each, and I found more than
>one which could run on win98SE,..no earlier tho.
>
>Went to a larger electronics place which sold printers etc and selected an
>end of run Epsom CX5500 (2007 model).
>
>I set it up and tried the next USB port and error message "cant communicate
>with USBPRNT1). Checked Epsoms copy function and all OK. The thing appears
>to be working.
>
>Tried removing the new KB. reinstate the old one with the 1/4" circle plug/
>This left the 2 USBs unused. Plugged Epsom into USB-1 reran the install CD,
>all OK, but when tried to print it still cant communicate with USB port.
>Appreciate any ideas on this,....Jason

Try one or other of the following USB device information utilities:
http://www.users.on.net/~fzabkar/USB_IDs/UVCView.x86.exe
http://www.users.on.net/~fzabkar/USB_IDs/usbview.exe

Can they see your printer?

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.

Jason James · Jun 24, 2008

"MEB" <meb@not here@hotmail.com> wrote in message
news:eRw6D5b1IHA.4492@TK2MSFTNGP02.phx.gbl...
> Need specs for computer - make and model
>
> You might try this:
> Make sure the device is NOT connected when installing the software, wait
> until it prompts you or restarts.
> Since you have already installed the device, remove and uninstall, and
> retry using this suggestion.
>
> Printer
> OPERATING SYSTEMS
> PRINTER DRIVERS Win 98SE/Me/2000/XP/XP x64/Vista, Mac OS 10.2.8 or later
> with USB / OS 10.5 Bundle available on CD
>
> INTERFACE
> INTERFACE USB 1.1 - Compatible with the USB 2.0 Specification
>
> Drivers/Software
>
http://tech.epson.co.nz/downloads/p...mailAdd=&MetricIDReturned=124875&platform=w98
>
> --
> MEB
> http://peoplescounsel.orgfree.com

Thanx MEB. I'll get back in a day or so. Ta...Jason

Jason James · Jun 24, 2008

"Franc Zabkar" <fzabkar@iinternode.on.net> wrote in message
news:u701649inul53bqn1sdh6ig28rm1vjlbd1@4ax.com...
> On Tue, 24 Jun 2008 12:59:18 +1000, "Jason James" <at@peace.com> put
> finger to keyboard and composed:
>
> >Howdy
> >
> > I found an office supply place who also sold printers/scanner/copiers
> >(allin one). They had spec sheets in frames for each, and I found more
than
> >one which could run on win98SE,..no earlier tho.
> >
> >Went to a larger electronics place which sold printers etc and selected
an
> >end of run Epsom CX5500 (2007 model).
> >
> >I set it up and tried the next USB port and error message "cant
communicate
> >with USBPRNT1). Checked Epsoms copy function and all OK. The thing
appears
> >to be working.
> >
> >Tried removing the new KB. reinstate the old one with the 1/4" circle
plug/
> >This left the 2 USBs unused. Plugged Epsom into USB-1 reran the install
CD,
> >all OK, but when tried to print it still cant communicate with USB port.
> >Appreciate any ideas on this,....Jason
>
> Try one or other of the following USB device information utilities:
> http://www.users.on.net/~fzabkar/USB_IDs/UVCView.x86.exe
> http://www.users.on.net/~fzabkar/USB_IDs/usbview.exe
>
> Can they see your printer?

Thanx Franc, I'll get back to the group in a day or so,..domestic duties

Jason

MEB · Jun 24, 2008

Jason James · Jul 1, 2008

"Jason James" <at@peace.com> wrote in message
news:4860961b$0$96056$c30e37c6@pit-reader.telstra.net...
>
> "Franc Zabkar" <fzabkar@iinternode.on.net> wrote in message
> news:u701649inul53bqn1sdh6ig28rm1vjlbd1@4ax.com...
> > On Tue, 24 Jun 2008 12:59:18 +1000, "Jason James" <at@peace.com> put
> > finger to keyboard and composed:
> >
> > >Howdy
> > >
> > > I found an office supply place who also sold
printers/scanner/copiers
> > >(allin one). They had spec sheets in frames for each, and I found more
> than
> > >one which could run on win98SE,..no earlier tho.
> > >
> > >Went to a larger electronics place which sold printers etc and selected
> an
> > >end of run Epsom CX5500 (2007 model).
> > >
> > >I set it up and tried the next USB port and error message "cant
> communicate
> > >with USBPRNT1). Checked Epsoms copy function and all OK. The thing
> appears
> > >to be working.
> > >
> > >Tried removing the new KB. reinstate the old one with the 1/4" circle
> plug/
> > >This left the 2 USBs unused. Plugged Epsom into USB-1 reran the install
> CD,
> > >all OK, but when tried to print it still cant communicate with USB
port.
> > >Appreciate any ideas on this,....Jason
> >
> > Try one or other of the following USB device information utilities:
> > http://www.users.on.net/~fzabkar/USB_IDs/UVCView.x86.exe
> > http://www.users.on.net/~fzabkar/USB_IDs/usbview.exe
> >
> > Can they see your printer?
>
> Thanx Franc, I'll get back to the group in a day or so,..domestic duties

Frank, I downloaded the first program (UVCView) and it worked well, It
identified the USB port number one, was connected to the Epson. No further
news on the printer. I tried another cable (A connector to USB), but no
change.

Jason

Jason James · Jul 1, 2008

"Jason James" <at@peace.com> wrote in message
news:486095d6$0$96056$c30e37c6@pit-reader.telstra.net...
>
> "MEB" <meb@not here@hotmail.com> wrote in message
> news:eRw6D5b1IHA.4492@TK2MSFTNGP02.phx.gbl...
> > Need specs for computer - make and model
> >
> > You might try this:
> > Make sure the device is NOT connected when installing the software,
wait
> > until it prompts you or restarts.
> > Since you have already installed the device, remove and uninstall, and
> > retry using this suggestion.
> >
> > Printer
> > OPERATING SYSTEMS
> > PRINTER DRIVERS Win 98SE/Me/2000/XP/XP x64/Vista, Mac OS 10.2.8 or later
> > with USB / OS 10.5 Bundle available on CD
> >
> > INTERFACE
> > INTERFACE USB 1.1 - Compatible with the USB 2.0 Specification
> >
> > Drivers/Software

MEB, what do you want me to do with the text above?

tks,..Jason

>
http://tech.epson.co.nz/downloads/p...mailAdd=&MetricIDReturned=124875&platform=w98
> >
> > --
> > MEB
> > http://peoplescounsel.orgfree.com
>
> Thanx MEB. I'll get back in a day or so. Ta...Jason
>
>

Franc Zabkar · Jul 1, 2008

On Wed, 2 Jul 2008 06:31:50 +1000, "Jason James" <at@peace.com> put
finger to keyboard and composed:

>> > Try one or other of the following USB device information utilities:
>> > http://www.users.on.net/~fzabkar/USB_IDs/UVCView.x86.exe
>> > http://www.users.on.net/~fzabkar/USB_IDs/usbview.exe
>> >
>> > Can they see your printer?
>>
>> Thanx Franc, I'll get back to the group in a day or so,..domestic duties
>

>
>Frank, I downloaded the first program (UVCView) and it worked well, It
>identified the USB port number one, was connected to the Epson. No further
>news on the printer. I tried another cable (A connector to USB), but no
>change.
>
>Jason

You've proved that the hardware is communicating OK. UVCView doesn't
require any device drivers to be installed, so it looks like a
software issue. I'd be trying what MEB suggested.

Otherwise go to Start -> Settings -> Printers, r-click your Epson,
select Properties -> Details, and look for any problems.

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.

Jason James · Jul 1, 2008

"Franc Zabkar" <fzabkar@iinternode.on.net> wrote in message
news:vf7l64ha0tggekpbovetltmf0vfjik18u3@4ax.com...
> On Wed, 2 Jul 2008 06:31:50 +1000, "Jason James" <at@peace.com> put
> finger to keyboard and composed:
>
> >> > Try one or other of the following USB device information utilities:
> >> > http://www.users.on.net/~fzabkar/USB_IDs/UVCView.x86.exe
> >> > http://www.users.on.net/~fzabkar/USB_IDs/usbview.exe
> >> >
> >> > Can they see your printer?
> >>
> >> Thanx Franc, I'll get back to the group in a day or so,..domestic
duties
> >

> >
> >Frank, I downloaded the first program (UVCView) and it worked well, It
> >identified the USB port number one, was connected to the Epson. No
further
> >news on the printer. I tried another cable (A connector to USB), but no
> >change.
> >
> >Jason
>
> You've proved that the hardware is communicating OK. UVCView doesn't
> require any device drivers to be installed, so it looks like a
> software issue. I'd be trying what MEB suggested.
>
> Otherwise go to Start -> Settings -> Printers, r-click your Epson,
> select Properties -> Details, and look for any problems.

Done. The port comment indicates the Epson, but has an in brackets note
saying "device is not connected". I'll mess around for a while then if nogo,
I'll try MEB's suggestions,

Jason

MEB · Jul 1, 2008

In news:486a9427$0$48621$c30e37c6@pit-reader.telstra.net at ,
Jason James contemplated and posted:
| "Jason James" <at@peace.com> wrote in message
| news:486095d6$0$96056$c30e37c6@pit-reader.telstra.net...
|>
|> "MEB" <meb@not here@hotmail.com> wrote in message
|> news:eRw6D5b1IHA.4492@TK2MSFTNGP02.phx.gbl...
|> > Need specs for computer - make and model
|> >
|> > You might try this:
|> > Make sure the device is NOT connected when installing the
|> > software, wait until it prompts you or restarts.
|> > Since you have already installed the device, remove and
|> > uninstall, and retry using this suggestion.
|> >
|> > Printer
|> > OPERATING SYSTEMS
|> > PRINTER DRIVERS Win 98SE/Me/2000/XP/XP x64/Vista, Mac OS 10.2.8 or
|> > later with USB / OS 10.5 Bundle available on CD
|> >
|> > INTERFACE
|> > INTERFACE USB 1.1 - Compatible with the USB 2.0 Specification
|> >
|> > Drivers/Software
|
| MEB, what do you want me to do with the text above?
|
| tks,..Jason

Hey you made it back,,,
The indications are that you must uninstall your prior failed
installation(s), cleanup *thoroughly* [check in the INF folder {likely in
the INF\OTHER\*.* folder}, re-start in Safe mode and check for "ghosts"
and/or old USB or driver leftovers and remove those then install the
software in Normal Mode *without* the printer connected, *until advised to
connect the printer*. Doing otherwise appears to cause installation issues,
likely related to Windows trying to control the USB (PnP) prior to software
installation. This happens more often with Network adapters, though other
USB devices may also require this installation order.
Some times you may be required to uninstall the USB Hub and secondaries to
clear the registry, so if there is still an issue try this using the above
but with this Hub removal in the Safe Mode cleanup/check, then try the
re-installation.

The interface information was crutial, but it shows that regardless of the
motherboard or adapter support {1.1 or 2.0} you will be able to use the
printer.

|
|>
|
http://tech.epson.co.nz/downloads/p...mailAdd=&MetricIDReturned=124875&platform=w98
|> >
|> > --
|> > MEB
|> > http://peoplescounsel.orgfree.com
|>
|> Thanx MEB. I'll get back in a day or so. Ta...Jason

--
MEB
http://peoplescounsel.orgfree.com
--
_________

Jason James · Jul 2, 2008

"MEB" <meb@not here@hotmail.com> wrote in message
news:%23p5ea6C3IHA.3384@TK2MSFTNGP04.phx.gbl...
> In news:486a9427$0$48621$c30e37c6@pit-reader.telstra.net at ,
> Jason James contemplated and posted:
> | "Jason James" <at@peace.com> wrote in message
> | news:486095d6$0$96056$c30e37c6@pit-reader.telstra.net...
> |>
> |> "MEB" <meb@not here@hotmail.com> wrote in message
> |> news:eRw6D5b1IHA.4492@TK2MSFTNGP02.phx.gbl...
> |> > Need specs for computer - make and model
> |> >
> |> > You might try this:
> |> > Make sure the device is NOT connected when installing the
> |> > software, wait until it prompts you or restarts.
> |> > Since you have already installed the device, remove and
> |> > uninstall, and retry using this suggestion.
> |> >
> |> > Printer
> |> > OPERATING SYSTEMS
> |> > PRINTER DRIVERS Win 98SE/Me/2000/XP/XP x64/Vista, Mac OS 10.2.8 or
> |> > later with USB / OS 10.5 Bundle available on CD
> |> >
> |> > INTERFACE
> |> > INTERFACE USB 1.1 - Compatible with the USB 2.0 Specification
> |> >
> |> > Drivers/Software
> |
> | MEB, what do you want me to do with the text above?
> |
> | tks,..Jason
>
> Hey you made it back,,,
> The indications are that you must uninstall your prior failed
> installation(s), cleanup *thoroughly* [check in the INF folder {likely in
> the INF\OTHER\*.* folder}, re-start in Safe mode and check for "ghosts"
> and/or old USB or driver leftovers and remove those then install the
> software in Normal Mode *without* the printer connected, *until advised to
> connect the printer*. Doing otherwise appears to cause installation
issues,
> likely related to Windows trying to control the USB (PnP) prior to
software
> installation. This happens more often with Network adapters, though other
> USB devices may also require this installation order.
> Some times you may be required to uninstall the USB Hub and secondaries
to
> clear the registry, so if there is still an issue try this using the above
> but with this Hub removal in the Safe Mode cleanup/check, then try the
> re-installation.
>
> The interface information was crutial, but it shows that regardless of
the
> motherboard or adapter support {1.1 or 2.0} you will be able to use the
> printer.
>
> |
> |>
> |
>
http://tech.epson.co.nz/downloads/p...mailAdd=&MetricIDReturned=124875&platform=w98

Thanx, this will take sometime. Inertially afflicted as I am with anything
these days There's driver files from at least one previous printer on board
as well. (HP printer)

Jason

MEB · Jul 2, 2008

In news:486b7d63$0$48620$c30e37c6@pit-reader.telstra.net at ,
Jason James contemplated and posted:
| "MEB" <meb@not here@hotmail.com> wrote in message
| news:%23p5ea6C3IHA.3384@TK2MSFTNGP04.phx.gbl...
|> In news:486a9427$0$48621$c30e37c6@pit-reader.telstra.net at ,
|> Jason James contemplated and posted:
|> | "Jason James" <at@peace.com> wrote in message
|> | news:486095d6$0$96056$c30e37c6@pit-reader.telstra.net...
|> |>
|> |> "MEB" <meb@not here@hotmail.com> wrote in message
|> |> news:eRw6D5b1IHA.4492@TK2MSFTNGP02.phx.gbl...
|> |> > Need specs for computer - make and model
|> |> >
|> |> > You might try this:
|> |> > Make sure the device is NOT connected when installing the
|> |> > software, wait until it prompts you or restarts.
|> |> > Since you have already installed the device, remove and
|> |> > uninstall, and retry using this suggestion.
|> |> >
|> |> > Printer
|> |> > OPERATING SYSTEMS
|> |> > PRINTER DRIVERS Win 98SE/Me/2000/XP/XP x64/Vista, Mac OS 10.2.8
|> |> > or later with USB / OS 10.5 Bundle available on CD
|> |> >
|> |> > INTERFACE
|> |> > INTERFACE USB 1.1 - Compatible with the USB 2.0 Specification
|> |> >
|> |> > Drivers/Software
|> |
|> | MEB, what do you want me to do with the text above?
|> |
|> | tks,..Jason
|>
|> Hey you made it back,,,
|> The indications are that you must uninstall your prior failed
|> installation(s), cleanup *thoroughly* [check in the INF folder
|> {likely in the INF\OTHER\*.* folder}, re-start in Safe mode and
|> check for "ghosts" and/or old USB or driver leftovers and remove
|> those then install the software in Normal Mode *without* the
|> printer connected, *until advised to connect the printer*. Doing
|> otherwise appears to cause installation issues, likely related to
|> Windows trying to control the USB (PnP) prior to software
|> installation. This happens more often with Network adapters, though
|> other USB devices may also require this installation order. Some
|> times you may be required to uninstall the USB Hub and secondaries
|> to clear the registry, so if there is still an issue try this using
|> the above but with this Hub removal in the Safe Mode cleanup/check,
|> then try the re-installation.
|>
|> The interface information was crutial, but it shows that regardless
|> of the motherboard or adapter support {1.1 or 2.0} you will be able
|> to use the printer.
|>
|> |
|> |>
|> |
|>
|
http://tech.epson.co.nz/downloads/p...mailAdd=&MetricIDReturned=124875&platform=w98
|
|
| Thanx, this will take sometime. Inertially afflicted as I am with
| anything these days There's driver files from at least one previous
| printer on board as well. (HP printer)
|
| Jason

Okay, as you have now indicated older files from other printers, make sure
to clean them up as well. You MAY find them listed in the INF\OTHER folder
as well.
Any *branded* software [device specific] may need removed also.

IF you have difficulties, you can try this:

Open the INFs found related to these printers and failed installations in a
text editor and look for the files and registry settings which were
used/installed for that device. Carefully remove/move those files and
registry settings [export prior to removal] to a temporary folder and watch
for errors occurring. IF no errors after a few days or a week of regular
usage, you can likely delete them. DO NOT remove files related to standard
Windows files [like mfc**, com**, odb**, ole**, std**, sti**, etc.], other
files should/must be checked by at least using Properties [or preferably
File Investigator, FileAlyzer, or some other like tool] *prior* to removal
and/or deletion.

Any questions or doubts on whether a file or registry setting is safe to
delete should be checked on the NET or in here.

--
MEB
http://peoplescounsel.orgfree.com
--
_________

Jason James · Jul 5, 2008

"MEB" <meb@not here@hotmail.com> wrote in message
news:ey6hcqH3IHA.1436@TK2MSFTNGP05.phx.gbl...
> In news:486b7d63$0$48620$c30e37c6@pit-reader.telstra.net at ,
> Jason James contemplated and posted:
> | "MEB" <meb@not here@hotmail.com> wrote in message
> | news:%23p5ea6C3IHA.3384@TK2MSFTNGP04.phx.gbl...
> |> In news:486a9427$0$48621$c30e37c6@pit-reader.telstra.net at ,
> |> Jason James contemplated and posted:
> |> | "Jason James" <at@peace.com> wrote in message
> |> | news:486095d6$0$96056$c30e37c6@pit-reader.telstra.net...
> |> |>
> |> |> "MEB" <meb@not here@hotmail.com> wrote in message
> |> |> news:eRw6D5b1IHA.4492@TK2MSFTNGP02.phx.gbl...
> |> |> > Need specs for computer - make and model
> |> |> >
> |> |> > You might try this:
> |> |> > Make sure the device is NOT connected when installing the
> |> |> > software, wait until it prompts you or restarts.
> |> |> > Since you have already installed the device, remove and
> |> |> > uninstall, and retry using this suggestion.
> |> |> >
> |> |> > Printer
> |> |> > OPERATING SYSTEMS
> |> |> > PRINTER DRIVERS Win 98SE/Me/2000/XP/XP x64/Vista, Mac OS 10.2.8
> |> |> > or later with USB / OS 10.5 Bundle available on CD
> |> |> >
> |> |> > INTERFACE
> |> |> > INTERFACE USB 1.1 - Compatible with the USB 2.0 Specification
> |> |> >
> |> |> > Drivers/Software
> |> |
> |> | MEB, what do you want me to do with the text above?
> |> |
> |> | tks,..Jason
> |>
> |> Hey you made it back,,,
> |> The indications are that you must uninstall your prior failed
> |> installation(s), cleanup *thoroughly* [check in the INF folder
> |> {likely in the INF\OTHER\*.* folder}, re-start in Safe mode and
> |> check for "ghosts" and/or old USB or driver leftovers and remove
> |> those then install the software in Normal Mode *without* the
> |> printer connected, *until advised to connect the printer*. Doing
> |> otherwise appears to cause installation issues, likely related to
> |> Windows trying to control the USB (PnP) prior to software
> |> installation. This happens more often with Network adapters, though
> |> other USB devices may also require this installation order. Some
> |> times you may be required to uninstall the USB Hub and secondaries
> |> to clear the registry, so if there is still an issue try this using
> |> the above but with this Hub removal in the Safe Mode cleanup/check,
> |> then try the re-installation.
> |>
> |> The interface information was crutial, but it shows that regardless
> |> of the motherboard or adapter support {1.1 or 2.0} you will be able
> |> to use the printer.
> |>
> |> |
> |> |>
> |> |
> |>
> |
>
http://tech.epson.co.nz/downloads/p...mailAdd=&MetricIDReturned=124875&platform=w98
> |
> |
> | Thanx, this will take sometime. Inertially afflicted as I am with
> | anything these days There's driver files from at least one previous
> | printer on board as well. (HP printer)
> |
> | Jason
>
> Okay, as you have now indicated older files from other printers, make
sure
> to clean them up as well. You MAY find them listed in the INF\OTHER folder
> as well.
> Any *branded* software [device specific] may need removed also.
>
> IF you have difficulties, you can try this:
>
> Open the INFs found related to these printers and failed installations in
a
> text editor and look for the files and registry settings which were
> used/installed for that device. Carefully remove/move those files and
> registry settings [export prior to removal] to a temporary folder and
watch
> for errors occurring. IF no errors after a few days or a week of regular
> usage, you can likely delete them. DO NOT remove files related to standard
> Windows files [like mfc**, com**, odb**, ole**, std**, sti**, etc.], other
> files should/must be checked by at least using Properties [or preferably
> File Investigator, FileAlyzer, or some other like tool] *prior* to removal
> and/or deletion.
>
> Any questions or doubts on whether a file or registry setting is safe to
> delete should be checked on the NET or in here.
>
> --
> MEB
> http://peoplescounsel.orgfree.com

Thanx for that MEB. ATM the printer is workingm and I did do a thorough
search for all named files and deleted them after checking them
"property-wise" I note that even this may not be sufficient. I wait in hope
the printer keeps working

. Thanx again.

Jason

Can't take a trick:Epsom CX5500 with win98SE

Jason James

MEB

Franc Zabkar

Jason James

Jason James

MEB

Jason James

Jason James

Franc Zabkar

Jason James

MEB

Jason James

MEB

Jason James

Similar threads